Combined regulator rectifier to replace separate items on Bosch equipped models. See our wiring instructions page for help installing this reg/rec.

Supplied with long leads for battery and alternator connection. Female spades for alternator and charge sensing, ring connectors for battery. NB this reg/rec should not be used with a lithium-ion battery

 1 in stock

Combined regulator rectifier to replace separate items on Bosch equipped models. See our wiring instructions page for help installing this reg/rec.

Includes harness extension with 6 spade connector block. NB this reg/rec should not be used with a lithium-ion battery

 Availability varies on this part, check availability

Left hand Domino type switchgear with high and low beam, pass, indicator and horn switches. Same style switch as ELA01738

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. An indication of wire colours is supplied with this switchgear. Supplied with 9 pin block connector. NB does not have lights off - park - on function, you need this to be on your RH switch (e.g. ELA01729 ) or run lights always on

 This part is available by special order, request a quote

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 This part is due back in stock soon, call 01484 841395 to reserve yours

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Coil clamp for round 12 volt coils

2 required per bike. No longer available new, call us to order used coil clamps

 Sorry, this part is no longer available.

CEV type lights (off/pilot/on), main beam and horn switch. Supplied without wires, you will need to solder your wiring into the switchgear using a minimum 60W soldering iron. Switch fixes to handlebars using included screws

Can be fitted to left or right side of bars

 This part is due back in stock soon, call 01484 841395 to reserve yours

12746001-z 12746001 GU12746001 12 74 60 01
 1274 6001 1274.6001 12.74.60.01

Old type 4 pin starter relay in metal case. Note that this has two large terminals and two smaller ones, depending on model you may need to fit wider spade connectors to fit this relay. See ELA10003 for large female spade connectors

 This part is due back in stock soon, call 01484 841395 to reserve yours

 12732500 GU12732500 12 73 25 00
 1273 2500 1273.2500 12.73.25.00

Oil pressure switch M12 thread, male spade connector

Superceded by ELA19670 . See ENA12640 for replacement crush washer if required

 Sorry, this part is no longer available.

 12768700 GU12768700 12 76 87 00
 1276 8700 1276.8700 12.76.87.00

12 volt single lead ignition coil

Suitable for points and Motoplat equipped big twins. NB models with Digiplex ignition use ELA30716. HT lead screws into this HT lead

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14716502 GU14716502 14 71 65 02
 1471 6502 1471.6502 14.71.65.02

Also fits Ducati, MZ ETZ 250/251

Rectifier / diode board for Bosch charging systems. High quaility replacement part sourced from Germany

See our Bosch fault finder page for help diagnosing problems on your Bosch charging system.

 This part is due back in stock soon, call 01484 841395 to reserve yours

17704300-z 17704300 GU17704300 17 70 43 00
 1770 4300 1770.4300 17.70.43.00